X8NiCrAITi32-21 1.4959 - NF EN 10028-7-2000

牌号	X8NiCrAITi32-21
	1.4959
对应标准	NF EN 10028-7-2000 压力容器用不锈钢扁平产品 Flat Products Made of Steels for Pressure Purposes Part 7: Stainless Steels
归类	奥氏体不锈钢
标签	标准等级
密度	8 g/cm³

X8NiCrAITi32-21 化学元素成分含量(%)

成分	C	Si	Mn	P	S	Cr	Ni	Cu	N	Ti	Co	Al	更多
最小值	0.05	-	-	-	-	19	30	-	-	0.25	-	0.25	Ni+Co:30~34
最大值	0.1	0.7	1.5	0.015	0.01	22	34	0.5	0.03	0.65	0.5	0.65	Ni+Co:30~34

◎ 未经买方同意，不得随意向钢中添加表中未列的元素，冶炼精加工除外。采取一切必要措施以防在废钢和生产原料中带入这些元素，因为其会削弱钢的机械性能，降低钢的适用性。

碳当量计算

X8NiCrAITi32-21 机械性能

条件	热处理或状态	抗拉强度 σ_b Mpa	屈服点 σ_s Mpa	断后伸长率或延伸率 δ %	冲击吸收能量 KV2 J
P：T ≤ 75	+AT	500~750	R_p0.2：≥170 R_p1.0：≥200 ①②	T ＜ 3mm: ≥30 T ≥ 3mm: ≥ 30 ②③	20℃： (l: ≥120；t: ≥80)

◎C- 冷轧带钢; H- 热轧带钢; P- 热轧中厚板；T- 厚度；t- 横向；l-纵向。
◎+A=软化退火；+AT=固溶退火；+QT=淬火及回火；+RA=再结晶退火。

◎ 如果热加工和随后冷却的条件符合ENISO3651-2中对产品机械性能和抗晶间腐蚀性的要求，则可以省略固溶处理。
*抗晶间腐蚀根据EN ISO 3651-2进行测试。在交货条件下：有；在致敏状态下：无。
① 对于连续热轧产品，可在询价和订购时商定Rp0.2(即表中σs)的最小值提高20MPa，Rp1.0的最小值提高10MPa。
② 如果在轧制宽度<300mm的带材情况下，采用纵向试验件，最小值减小如下:抗拉强度-15MPa，恒定标距的延伸率-5%，比例标距延伸率-2%。
③ T＜3mm：该值适用于标距为80mm、宽度为20mm的试件，也可以使用标距为50mm、宽度为12.5mm的试件。T ≥3mm：该值适用于标距为5.65√S的试件。

高温下的最小屈服强度

Material designation		Heat treatment condition	Minimum 0.2% proof strength R_p0.2,MPa at a temperature (in°C) of:
Name	Number	Heat treatment condition	100	150	200	250	300	350	400	450	500	550	600
X8NiCrAITi32-21	1.4959	+AT	140	127	115	105	95	90	85	82	80	75	75
			Minimum 1.0% proof strength R_p1.0,MPa at a temperature (in°C) of:
			100	150	200	250	300	350	400	450	500	550	600
			160	147	135	125	115	110	105	102	100	95	95

高温下的最小抗拉强度

Material designation Minimum tensile strength R_m,MPa
at a temperature (in°C) of:
Name Number 100 150 200 250 300 350 400 450 500 550 600
X8NiCrAITi32-21 1.4959 465 445 435 425 420 418 415 415 415 - -

热处理指南

Material designation		Hot forming		Heat treatment symbol	Solution anneailing ①②		Post weld heat treatment Creep resisting steels
Name	Number	Temperature ℃	Type of cooling	Heat treatment symbol	Temperature ℃ ③④	Type of cooling	Temperature ℃ ⑦	Type of cooling
X8NiCrAITi32-21	1.4959	1150 to 850	air	+AT	1100 to 1200 ⑤	water,air ⑥	900 to 950 ⑧	air

◎ a=air; o=oil; w=water.
◎ Scale and annealing colours produced during hot forming, heat treatment or welding may adversely affect the corrosion resistance. They should be removed as far as possible before use, e.g. by pickling.
◎ The temperatures of annealing should be agreed for simulated heat treated test pieces.
① The solution treatment may be omitted if the conditions for hot working and subsequent cooling are such that the requirements for the mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained and provided these requirements are met even after appropriate subsequent solution annealing.
② Re-crystallizing annealing.
③ If heat treatment is carried out in a continuous furnace, the upper part of the range specified is usually preferred, or even exceeded.
④ The lower end of the range specified for solution annealing should be aimed at for heat treatment as part of further processing,because otherwise the mechanical properties might be affected. If the temperature of hot forming does not drop below the lower temperature for solution annealing.a temperature of 980℃ is adequate as a lower limit for Mo-free steels,a temperature of 1000℃ for steels with Mo contents up to 3% and a temperature of 1020℃ for steets with Mo contents exceeding 3%.

⑤ After solution annealing the grain size according to EN ISO 643 shall be 1 to 5.

⑥ cooling sufficiently rapid.

⑦ Minimum holding time:30min.Minimum holding time:30min.

⑧ Minimum holding time:30min.

物理性能

Modulus of elasticity at											Mean coefficient of thermal expansion between 20 ℃ and										Thermal conductivity at 20℃	Specific thermal capacity at 20℃	Specific electrical resistivity at 20℃
20°C	100°C	200°C	300°C	400°C	500°C	600°C	700°C	800°C	900°C	1000°C	100°C	200°C	300°C	400°C	500°C	600°C	700°C	800°C	900°C	1000°C	Thermal conductivity at 20℃	Specific thermal capacity at 20℃	Specific electrical resistivity at 20℃
KN/mm²											10^-6 K^-1										W/m.K	J/kg.K	Ω.mm²/m
200	190	185	175	170	160	155	145	140	135	125	15.4	16	16.5	16.8	17.2	17.5	17.9	18.3	18.6	19	12	460	0.99

蠕变性能

Designation		Heat treatment condition	Temperature	Strength for rupture							Strength for 1% (plastic) creep strain
Designation			Temperature	in N/mm² for ①
Name	Number		°C	10000h	30000h	50000h	100000h	150000h	200000h	250000h	10000h	100000h
X8NiCrAITi32-21	1.4959	+AT	700	73	58.2	-	44.8	-	38.2	-	59	42
			710	67.8	54	-	41.4	-	35.2	-	55.5	38
			720	63	50.1	-	38.3	-	32.5	-	52	34.4
			730	58.5	46.5	-	35.4	-	30	-	48.5	31.3
			740	54.4	43.1	-	32.8	-	27.7	-	45	28.4
			750	50.6	40	-	30.3	-	25.6	-	41.7	26
			760	47	37.1	-	28	-	23.6	-	38.4	23.5
			770	43.7	34.4	-	25.9	-	21.8	-	35.6	21.3
			780	40.7	31.9	-	24	-	20.1	-	32.9	19.3
			790	37.8	29.6	-	22.1	-	18.5	-	30.5	17.6
			800	35.2	27.4	-	20.4	-	17	-	28.2	16
			810	32.7	25.4	-	18.9	-	15.6	-	26.2	14.7
			820	30.4	23.6	-	17.4	-	14.4	-	24.2	13.4
			830	28.3	21.8	-	16	-	13.2	-	22.4	12.1
			840	26.3	20.2	-	14.8	-	12.1	-	20.8	11.1
			850	24.4	18.7	-	13.6	-	11.1	-	19.1	10
			860	22.7	17.3	-	12.5	-	10.1	-	17.6	9.1
			870	21	16	-	11.5	-	9.23	-	16.1	8.2
			880	19.5	14.8	-	10.5	-	8.41	-	14.7	7.3
			890	18.1	13.6	-	9.6	-	7.63	-	13.4	6.5
			900	16.8	12.6	-	8.76	-	6.91	-	12.1	5.7
			910	15.6	11.6	-	7.98	-	6.23	-	10.9	5
			920	14.4	10.6	-	7.25	-	5.6	-	9.8	4.4
			930	13.3	9.77	-	6.57	-	5.01	-	8.8	3.9
			940	12.3	8.95	-	5.93	-	4.45	-	7.8	3.4
			950	11.4	8.19	-	5.33	-	3.93	-	6.9	2.9
			960	10.5	7.47	-	4.77	-	3.43	-	6.1	2.5
			970	9.63	6.8	-	4.23	-	2.95	-	5.3	2.1
			980	8.85	6.17	-	3.73	-	-	-	4.6	1.8
			990	8.11	5.57	-	3.25	-	-	-	4	1.6
			1000	7.42	5.01	-	2.79	-	-	-	3.5	1.4

◎ Values were taken from DIN 17460.
① Values in parantheses involved time and/or stress extrapolation; values with asterisk involved time extrapolation.

材料牌号对应供应商

告诉我在“材数库”看到，将给您优惠

东台市汇信诚金属制品厂

主营: 六角螺帽螺杆双头牙条活节垫片螺钉销非标紧固件特材紧固件

联系人：沈经理
移动电话： 13770090340/13390704526
电话：0515-85522226
微信号：13770090340

不锈钢紧固件系列、不锈钢螺帽系列、A4-80外六角系列、A4-80外六角系列、德标加大加长系列、国标冷镦车削系列、键销系列、钻孔螺杆系列、销系列、不脱出螺钉系列、薄头内六角螺钉系列、半圆头/压铆件系列、铰制孔螺杆系列、紧定螺钉系列、沉头螺钉系列、有色金属制品系列、异型螺母系列、牙条双头系列、连接杆系列、折弯件系列、阀门配件系列、防盗杆系列、管接头系列、螺塞堵头系列、非标紧固件、特殊材质紧固件等。

询价

无锡新傲五金机电有限公司

主营: 六角螺母六角头螺栓全螺纹螺柱双头螺柱烟机螺栓螺母非标定制国标紧固件行业紧固件美标紧固件德标紧固件米制、英制高强度紧固件等

联系人：陈先生
移动电话： 15298415285
微信号：15298415285

不锈钢六角螺母，六角头螺栓，内六角螺栓，全螺纹螺柱，双头螺柱，堵头，紧定螺栓，可按国标、行标、美标及德标等国内外标准生产不锈钢产品，高温合金产品，也可按用户要求设计和制造非标准紧固件。

询价

X8NiCrAITi32-21 对应不同标准

1	NF EN 10088-1-2005 不锈钢 - 第1部分：不锈钢清单
	X8NiCrAITi32-21 1.4959
2	NF EN 10028-7-2008 压力容器用不锈钢扁平产品
	X8NiCrAITi32-21 1.4959
3	NF EN 10028-7-2000 压力容器用不锈钢扁平产品
	X8NiCrAITi32-21 1.4959

注：数据仅供参考！如有疑问，请填写"我要纠错"！

Material designation		Minimum tensile strength R_m,MPa at a temperature (in°C) of:
Name	Number	100	150	200	250	300	350	400	450	500	550	600
X8NiCrAITi32-21	1.4959	465	445	435	425	420	418	415	415	415	-	-

高温下的最小屈服强度

高温下的最小抗拉强度

热处理指南

物理性能

蠕变性能

材料牌号对应供应商