牌号 X19CrMoNbVN11-1
1.4913
对应标准 NF EN 10269-1999
用于高温或低温条件下的紧固件用钢及镍合金
归类 合金钢
标签 淬火回火钢
密度 7.7 g/cm3
X19CrMoNbVN11-1 化学元素成分含量(%)
成分 C Si Mn P S Cr Ni Mo N V Nb B Al
最小值 0.17 - 0.4 - - 10 0.2 0.5 0.05 0.1 0.25 - -
最大值 0.23 0.5 0.9 0.025 0.015 11.5 0.6 0.8 0.1 0.3 0.55 0.0015 0.02
◎ 未经买方同意,不得随意向钢中添加表中未列的元素,冶炼精加工除外。采用一切必要措施以防在废钢和生产原料中带入这些元素,因为其会削弱钢的机械性能,降低钢的适用性
X19CrMoNbVN11-1 机械性能
直径
d
mm
热处理或状态
抗拉强度
σb
Mpa
屈服点
σs
Mpa
断后伸长率或延伸率
δ
%
断面收缩率
ψ
%
硬度
HBW
冲击吸收能量
KV2
J
-* +A - - - - ≤302 -
d≤160** +QT 900~1050 ≥750 ≥12 ≥40 - ≥20
◎ +AT=固溶退火;+C=冷作硬化;+N=正火;+NT=正火及回火;+P=沉淀硬化;+QT=淬火及回火;WW=热作硬化;+AC=球化退火;+A=软化退火;+S=冷剪处理(treated for cold shearing)
*通常适用于进一步加工交货条件下的常温机械性能
**由此生产并经热处理的产品不符合97/23/EC的基本要求

  • 交付条件下在高温下的最小屈服强度

    Material designationHeat treatment
    condition
    Diameter
    d
    mm
    Minimum 0.2%-proof strength Rp0.2 in MPa at a temperature (in°C) of:
    Name Number50100150200250300350400450500550600650
    X19CrMoNbVN11-11.4913+QTd≤160726701676651643627610577544495412305-

  • 符合本欧洲标准的产品热处理指南

    Material designationHeat treatment
    condition
    Normalizing,quenching
    or solution annealing
    temperature
    °C
    Type of
    cooling
    Tempering or
    precipitation
    treatment (and time)
    °C
    Name Number
    X19CrMoNbVN11-11.4913+QT1100 to 1130a,o670 to 720(min.2 h)
    ◎ 根据原件相关规定,如果允许矫直后消除应力,应选择消除应力的温度,以获得规定的性能。
    ① a=air; o=oil; w=water



  • 物理性能

    各温度°C时静态弹性模量
    20 100 200 300 400 500 600 700 800
    GPa
    216 209 200 190 179 167 127 - -

  • 蠕变性能

    DesignationTemperatureStrength for
    1% (plastic)
    creep strain ①
    Creep rupture
    strength for ②
    Name Number°C10000h100000h10000h100000h200000h
    X19CrMoNbVN11-11.4913450500448559500486
    460475416529472450
    470450388500444425
    480424358473414395
    490398328446383364
    500374298417349330
    510349268392314291
    520323238366276253
    530298210340237209
    540274181314201172
    550250153288161130
    560225-259132102
    570201-23410581
    580177-2088666
    590154-1817252
    600133-1556549
    ◎ The values given in this table are the mean values of the scatter band so far obtained, which will be checked from time to time as further test results become available and if necessary corrected.
    ◎ * and () indicate values of extended stress extrapolation or time extrapolation, respectively.
    ① This is the stress relative to the initial cross- section leadina to a permanent elongation of 1 % after 10000 h and 100000 h.
    ② This is the stress relative to the initial cross- section leading to fracture after 10000 h, 100000 h and 200000 h.


  • 松弛性能

    Material designationTemperature

    for an
    initial strain
    A total
    %
    Residual stress in N/mm2
    after stressing duration for
    Name Number1000
    h
    10000
    h
    30000
    h
    X19CrMoNbVN11-11.49134000.2262237206
    410257231202
    420252225199
    430246218195
    440240212190
    450234206185
    460228198180
    470221191173
    480214183165
    490207175157
    500199166147
    510190155136
    520181143124
    530171130108
    54016011492
    5501499879
    5601347866
    5701186353
    5801004840
    590803930
    600613021
    ◎ The values given in this table are the mean values of the scatter band so far obtained, which will be checked from time to time as further test results become available and if necessary corrected.


X19CrMoNbVN11-1 对应不同标准
1 EN 10088-1-2005 不锈钢 第1部分:不锈钢的清单
2 EN 10269-2006 规定高温和/或低温性能的紧固件用钢和镍合金
3 EN 10302-2008 镍和镍钴合金的耐蠕变钢
4 EN 10269-2013 规定高温和/或低温性能的紧固件用钢和镍合金
5 GB /T 3098.24-2020 紧固件机械性能 高温用不锈钢和镍合金螺栓、螺钉、 螺柱和螺母
6 NF EN 10269-1999 用于高温或低温条件下的紧固件用钢及镍合金
7 DIN EN 10269-2014 规定高温和/或低温性能的紧固件用钢和镍合金
8 NF EN 10088-1-2005 不锈钢 - 第1部分:不锈钢清单
注:数据仅供参考!如有疑问,请填写"我要纠错"!
版权说明:
⑴ 本网站的所有内容(包括但不限于文字、图片、音频、视频等)均受到版权保护,版权归本网站所有;
⑵ 未经授权,禁止以任何形式转载、复制、传播或用于其他商业用途;
⑶ 如需使用本网站内容,请提前获得授权。